LV8862JA Bi-CMOS LSI www.onsemi.com Single-phase FAN Motor Driver Overview LV8862JA is a driver IC used for single-phase fan motor. High-efficiency and low-noise are realized by reducing reactive power using Silent PWM. This ICs feature is low on-resistance 0.6 & High-efficiency. Therefore, it is optimal for high power fan motor and home appliance equipment. Feature Single-phase full wave operation by Silent PWM drive Speed is controllable by PWM input SSOP16 (225mil) Hall bias output pin Integrated Quick Start Circuit FG (rotation detection)/ RD (lock detection) output pin (open drain output) Integrated current limiter circuit (limit at Io=500mA with RL=0.5 connection, limit value is determined based on Rf.) Integrated lock protector circuit and automatic recovery circuit Integrated thermal shut-down (TSD) circuit Typical Applications Fan motor units Desk top PCs Refrigerator Projectors Specifications Absolute Maximum Ratings at Ta = 25C, GND = 0V Parameter Symbol Conditions Ratings Unit Maximum supply voltage VCCmax 20 V OUT pin output current IOUTmax 1.5 A Output withstand VOUTmax 20 V RD/FG output pin withstand VRD/FG max 18 V RD/FG output maximum current IRD/FG max 10 mA RGL output maximum current IRGL max 5 mA HB output maximum current IHB max 10 mA 6 PWM input pin withstand VPWM max V On a specified board *1 0.8 Allowable power dissipation Pd max W *2 Operating temperature Topr 40 to + 95 C Storage temperature Tstg 55 to + 150 C *1 Specified board: 76.1mm x 114.3mm x 1.6mm, glass epoxy board *2 Do not exceed Tjmax=150 C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. ORDERING INFORMATION See detailed ordering and shipping information on page 12 of this data sheet. Semiconductor Components Industries, LLC, 2015 1 Publication Order Number : March 2015 - Rev. 1 LV8862JA/D LV8862JA Recommended Operating Conditions at Ta = 25C, GND = 0V Parameter Symbol Conditions Ratings Unit Operating supply voltage range VCC op1 Recommended supply voltage range 3.6 to 16 V Hall input common phase input VICM 0.3 to VRGL 1.5 V voltage range PWM pin input voltage range PWM 0 to 5.5 V SSW pin input voltage range SSW 0 to VRGL V Input PWM frequency range PWMF 20 to 50 kHz Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. Electrical Characteristics at Ta 25 C, V = 12V, GND = 0V CC Ratings Parameter Symbol Conditions Unit min typ max ICC Active 2.5 3.5mA Circuit consumption current ICCo Stand-by 2.0 3.0mA RGL pin output voltage VRGL 3.0 3.15 3.3 V HB pin output voltage VHB IHB=5mA 1.16 1.25 1.28 V Output ON resistance Ron Io=1.0A, upper + lower ON resistance 0.6 0.8 Hall input bias current IHIN 1.0 A Current limiter VRF 220 250 280 mV PWM pin input Low level VPWML 0 1.0 V PWM pin input High level VPWMH 2.0 VRGL V PWM input minimum pulse width TPWM 1 Sec RD/FG output pin Low voltage VRD/FG IRD/FG=3mA 0.22 0.30 V FG output leakage current IRDL/FGL VRD/FG=18V 10 A FG comparator hysteresis width VHYS including offset 5 12 18 mV Output ON time in Lock-detection TACT 0.6 0.8 1.0 Sec Output OFF time in Lock-detection TDET 6 7.2 9 Sec Output ON/OFF ratio in TRTO TRTO=TDET/TACT 7.5 9.0 11.0 Lock-detection Thermal shutdown operating TSD 180 C *Design guarantee temperature Thermal shutdown hysteresis width TSD *Design guarantee 40 C Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Truth table Operating state IN1 IN2 PWM OUT1 OUT2 FG RD L H H L L L H Rotation drive mode H L L H OFF L L H L L L L Rotation regeneration mode L H L L L OFF L L H OFF L L OFF Lock protector H L L OFF OFF OFF www.onsemi.com 2