NLAS2750 Low Voltage Dual SPDT Analog Switch with Negative Swing Audio Capability www.onsemi.com The NLAS2750 is a dual SPDT low onresistance analog switch. It can operate from a single 1.8 V to 5.0 V power supply. It is a MARKING bidirectional switch that can switch a negative voltage swing audio DIAGRAM signal without requiring a coupling capacitor. With a single power supply, the audio signal can swing over the range from 2.5 V to V . CC UQFN10 ALM CASE 488AT Features 1 Capable to Switch Negative Swing Audio Signals Without Requiring a DC Blocking Capacitor AL = Specific Device Code Low Onresistance (R ) ON M = Date Code/Assembly Location = PbFree Device Low Voltage Digital Control Logic: (Note: Microdot may be in either location) (V = 1.4 V V = 2.7 V to 4.3 V) INH CC Low Power Consumption (I 250 nA) CC Space Saving 1.4 mm x 1.8 mm Package UQFN Package GND NC2 This is a PbFree Device 76 Typical Applications IN2 8 5 NC1 Cellular Phones Portable Media Players COM2 9 4 IN1 NO2 10 3 COM1 12 V CC NO1 FUNCTION TABLE IN1 (Pin 4) IN2 (Pin 8) Function 0 X COM1 = NC1 1 X COM1 = NO1 X 0 COM2 = NC2 X 1 COM2 = NO2 ORDERING INFORMATION See detailed ordering and shipping information on page 7 of this data sheet. Semiconductor Components Industries, LLC, 2015 1 Publication Order Number: April, 2015 Rev. 3 NLAS2750/DNLAS2750 COM NO NC IN Figure 1. Logic Equivalent Circuit MAXIMUM RATINGS Symbol Parameter Value Unit V Positive DC Supply Voltage 0.3 to +6.5 V CC V Analog Input Voltage (COM, NO, NC) (Notes 1 and 2) Min. V = V 6.5 V or V IS IS CC 2.5 V (whichever is greater) Max. V = V + 0.3 V IS CC V Digital (IN1, IN2) 0.3 to +6.5 V IN I Current (GND, V ) 50 mA CC CC I Continuous Switch Current (COM, NO, NC) (Note 1) 250 mA IS I Peak Switch Current (Pulsed at 1 ms, 10% Duty Cycle) 500 mA ISP T Storage Temperature 65 to +150 C STG P Power Dissipation 200 mW D V ESD (Human Body Model) kV ESD All pins 6 I/O to GND 8 I Latchup (per JESD78) 300 mA LU Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Signals on COM, NO, NC, exceeding V will be clamped by internal diodes. Limit forward diode current to maximum current ratings. CC 2. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum is used in this data sheet. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit V Power Supply Range 1.8 5.5 V CC V Digital Select Input Voltage Overvoltage Tolerance (OVT) (IN1, IN2) GND 5.5 V IN V Analog Input Voltage (NC, NO, COM) (Note 3) 2.5 V V IS CC T Operating Temperature Range 40 +85 C A t , t Input Rise or Fall Time (IN1, IN2) ns/V r f V < 2.7 V 20 CC V 2.7 V 10 CC Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 3. The voltage across the switch should be 5.5 V. www.onsemi.com 2