SID1112K Power Integrations

SID11x2K SCALE-iDriver Family Up to 8 A Single Channel IGBT/MOSFET Gate Driver Providing Reinforced Galvanic Isolation Product Highlights Description Highly Integrated, Compact Footprint The SID11x2K is a single channel IGBT and MOSFET driver in an Split outputs providing up to 8 A peak drive current eSOP package. Reinforced galvanic isolation is provided by Power Integrated FluxLink technology providing safe isolation between Integrations innovative solid insulator FluxLink technology. The up to primary-side and secondary-side 8 A peak output drive current enables the product to drive devices up Rail-to-rail stabilized output voltage to 450 A (typical) without requiring any additional active components. Unipolar supply voltage for secondary-side For gate drive requirements that exceed the stand-alone capability of Suitable for 600 V / 650 V / 1200 V IGBT and MOSFET switches the SID1182Ks, an external amplifier (booster) may be added. Stable Up to 250 kHz switching frequency positive and negative voltages for gate control are provided by one Low propagation delay time 260 ns unipolar isolated voltage source. Propagation delay jitter 5 ns Additional features such as short-circuit protection (DESAT) with -40 C to 125 C operating ambient temperature Advanced Soft Shut Down (ASSD), undervoltage lock-out (UVLO) for High common-mode transient immunity primary-side and secondary-side and rail-to-rail output with tempera- eSOP package with 9.5 mm creepage and clearance ture and process compensated output impedance guarantee safe Advanced Protection / Safety Features operation even in harsh conditions. Undervoltage lock-out protection for primary and secondary-side Controller (PWM and fault) signals are compatible with 5 V CMOS logic, (UVLO) and fault feedback which may also be adjusted to 15 V levels by using external resistor divider. Short-circuit protection using V monitoring and fault feedback CESAT Advanced Soft Shut Down (ASSD) Product Portfolio Full Safety and Regulatory Compliance 1 Product Peak Output Drive Current 100% production partial discharge test 100% production HIPOT compliance testing at 6 kV RMS 1 s SID1112K 1.0 A Reinforced insulation meets VDE 0884-10 SID1132K 2.5 A Green Package SID1152K 5.0 A Halogen free and RoHS compliant SID1182K 8.0 A Applications Table 1. SCALE-iDriver Portfolio. General purpose and servo drives Notes: 1. Package: eSOP-R16B. UPS, solar, welding inverters and power supplies Figure 2. eSOP-R16B Package. SCALE-iDriver VCE Primary-Side Secondary-Side Logic Logic VGXX IN VISO Fault Output SO V TOT GH V IN VCC FluxLink GL V VCC GND VEE COM PI-7949-072616 Figure 1. Typical Application Schematic. www.power.com May 2018 This Product is Covered by Patents and/or Pending Patent Applications. - + - +SID11x2K VCE V DES VGXX COM SHORT-CIRCUIT BOOTSTRAP VISO DETECTION CHARGE PUMP VCC LEVEL ASSD SHIFTER GH FluxLink SO TRANSCEIVER TRANSCEIVER (BIDIRECTIONAL) (BIDIRECTIONAL) VISO GL GND CORE LOGIC SUPPLY MONITORING AUXILIARY CORE LOGIC COM POWER SUPPLIES SUPPLY IN MONITORING VISO AUXILIARY POWER SUPPLIES VEE CONTROL VEE PI-7654-092216 Figure 3. Functional Block Diagram. VISO Pin (Pin 14): Pin Functional Description This pin is the input for the secondary-side positive supply voltage. VCC Pin (Pin 1): COM Pin (Pin 15): This pin is the primary-side supply voltage connection. This pin provides the secondary-side reference potential. GND Pin (Pin 3-6): GL Pin (Pin 16): This pin is the connection for the primary-side ground potential. This pin is the driver output sinking current (turn-off). All primary-side voltages refer to the pin. IN Pin (Pin 7): This pin is the input for the logic command signal. SO Pin (Pin 8): This pin is the output for the logic fault signal (open drain). NC Pin (Pin 9): VCC 1 16 GL This pin must be un-connected. Minimum PCB pad size for soldering 15 COM is required. 14 VISO VEE Pin (Pin 10): 13 GH GND 3-6 Common (IGBT emitter/MOSFET source) output supply voltage. 12 VGXX VCE Pin (Pin 11): 11 VCE This pin is the desaturation monitoring voltage input connection. IN 7 10 VEE SO 8 9 NC VGXX Pin (Pin 12): This pin is the bootstrap and charge pump supply voltage source. GH Pin (Pin 13): This pin is the driver output sourcing current (turn-on) connection. PI-7648-041415 Figure 4. Pin Configuration. 2 Rev. G 05/18 www.power.com +