PM5432.223NLT Pulse

SMT Power Inductors High Current Composite Inductor - PA5432.XXXNLT and PM5432.XXXNLT POWER PRODUCTS Height: 6.0mm Max Footprint: 6.8mm x 6.6mm Max Current Rating: up to 10.5Arms Inductance Range: 4.7uH to 22uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5432) and Automotive (PM5432) grades Electrical Specifications 25C, Operating Temperature -55C to +155C Saturation Heating 2 4 Part Number DC Resistance Current SRF Inductance Rated K Factor Current (25C) 100KHz, 0.1V Current for TYP. MAX. TYP. T 40C TYP. Core Loss 7 7 Commerical Automotive uH20% A m m A A MHz PA5432.472NLT PM5432.472NLT 4.7 10.5 13.10 14.4 10.5 11 21 - PA5432.562NLT PM5432.562NLT 5.6 9.9 14.46 15.9 9.9 10 20 - PA5432.682NLT PM5432.682NLT 6.8 9 18.90 20.8 9.2 9 18 - PA5432.822NLT PM5432.822NLT 8.2 8 24.00 26.4 8.4 8 16 - PA5432.103NLT PM5432.103NLT 10 7 27.00 29.82 7.6 7 14 - PA5432.153NLT PM5432.153NLT 15 6 39.77 43.75 5.8 6 11 - PA5432.223NLT PM5432.223NLT 22 5 55.12 60.63 5.6 5 9 - Notes: 1. Actual temperature of the component during system operation (ambient plus 5. The part temperature (ambient+temp rise) should not exceed 155C under worst temperature rise) must be within the standard operating range. case operating conditions. Circuit design, PCB trace size and thickness, airflow and 2. The saturation current is the current at which the initial inductance drops by ap- other cooling provisions all affect the part temperature. Part temperature should be proximately 30% at the stated ambient temperature. The maximum allowable drop verified in the end application. at this stated current is 40% of the initial inductance. This current is determined by 6. Parts shown in bold are standard catalog parts and are available through sample placing the component in the specified ambient environment and applying a short stock and distribution. Parts in lighter font are available but are not necessarily held duration pulse current (to eliminate self-heating effect) to the component. in sample stock or distribution and lead times may be longer. Please contact Pulse 3. The Heating current is the DC current required to raise the component tempera- for availablity. ture by approximately 40C. Take note that the components performanc varies 7. The PM5432.XXXNLT part numbers are also IATF16949 certified. The mechanical depending on the system condition. It is suggested that the component be tested dimensions are100% tested in production but do not necessarily meet a product at the system level, to verify the temperature rise of the component during system capability index (Cpk) 1.33 and therefore the PM5432.XXXNLT may not strictly operation. conform to PPAP. 4. The rated current as listed is either the saturation current or the heating current ( 8. Special Characteristics T 40C) depending on which value is lower. Power.PulseElectronics.com P890.A (04/20) 1SMT Power Inductors High Current Composite Inductor - PA5432.XXXNLT and PM5432.XXXNLT POWER PRODUCTS Mechanical PA5432.XXXNLT and PM5432.XXXNLT D A C H E XXXNL 1R2 B F 16D/C02 FINAL LAYOUT SUGGESTED PAD LAYOUT Series A B C D E F L G H PA5432/PM5432 6.8 6.6 6.0 5.6 1.7 2.9 5.6(REF) 2.5 (REF) 5.6 (REF) All Dimensions in mm. TAPE & REEL INFO SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA5432/PM5432 330 16.4 12 16 6.3 750 For More Information: Americas - prodinfo power pulseelectronics.com Europe - power-apps-europe pulseelectronics.com Asia - power-apps-asia pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. Copyright, 2020. Pulse Electronics, Inc. All rights reserved. Power.PulseElectronics.com P890.A (04/20) 2 POWER PRODUCTS L G