R1800F

R1200F THRU R2000F HIGH VOLTAGE FAST RECOVERY RECTIFIER VOLTAGE RANGE 1200 to 2000 Volts CURRENT 0.2 to 0.5 Ampere FEATURES *Fast switching *Low leakage *High current capability *High surge capability *High reliability MECHANICAL DATA * Case: Molded plastic *Epoxy: Device has UL flammability classification 94V-O .034 (0.9) DIA. *Lead: MIL-STD-202E method 208C guaranteed .028 (0.7) 1.0 (25.4) MIN. *Mounting position: Any *Weight: 0.35 gram .205 (5.2) .166 (4.2) .107 (2.7) DIA080 (2.0) 1.0 (25.4) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS MIN. o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) o MAXIMUM RATINGS (At TA = 25 C unless otherwise noted) RATINGS SYMBOL R1200F R1500F R1800F R2000F UNITS Maximum Recurrent Peak Reverse Voltage VRRM 1200 1500 1800 2000 Volts Maximum RMS Volts VRMS 840 1050 1260 1400 Volts Maximum DC Blocking Voltage VDC 1200 1500 1800 2000 Volts Maximum Average Forward Rectified Current IO 500 200 o mAmps at TA = 50 C Peak Forward Surge Current, 8.3 ms single half sine-wave IFSM 30 Amps superimposed on rated load (JEDEC method) 2 2 Typical Current Squarad Time I t A /Sec 3.74 0 Operating and Storage Temperature Range TJ, TSTG -65 to + 175 C o ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) CHARACTERISTICS SYMBOL R1200F R1500F R1800F R2000F UNITS Maximum Instantaneous Forward Voltage at 0.5A/0.2A DC VF 2.5 4.0 Volts Maximum DC Reverse Current 5.0 uAmps o at Rated DC Blocking Voltage TA = 25 C IR Maximum Full Load Reverse Current Average, Full Cycle o 100 uAmps .375, (9.5mm) lead length at TL = 55 C Maximum Reverse Recovery Time (Note) trr 500 nSec NOTES : Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2016-09 REV:AR1200F~R1800F R2000F ( ) RATING AND CHARACTERISTIC CURVES R1200F THRU R2000F FIG. 1 - TYPICAL FORWARD CURRENT FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD DERATING CURVE SURGE CURRENT 70 500 Single Phase Half Wave 60Hz Inductive or 60 8.3ms Single Half Sine-Wave 400 Resistive Load (JEDEC Method) 50 300 40 30 200 20 100 10 0 0 0 50 100 150 175 1 10 100 AMBIENT TEMPERATURE, ( ) NUMBER OF CYCLES AT 60Hz FIG. 3 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 10 NONINDUCTIVE NONINDUCTIVE trr +0.5A ( - ) D.U.T ( + ) PULSE 0 25 Vdc GENERATOR (approx) (NOTE 2) -0.25A ( - ) 1 OSCILLOSCOPE ( + ) NON- (NOTE 1) INDUCTIVE -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1cm SET TIME BASE FOR 1 megohm. 22 pF. 50/100 ns/cm 2. Rise Time = 10ns max. Source Impedance = 50 ohms. RECTRON AVERAGE FORWARD CURRENT, (mA) PEAK FORWARD SURGE CURRENT, (A)