IDT2308 3.3V ZERO DELAY CLOCK MULTIPLIER COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES 3.3V ZERO DELAY IDT2308 CLOCK MULTIPLIER FEATURES: DESCRIPTION: Phase-Lock Loop Clock Distribution for Applications ranging The IDT2308 is a high-speed phase-lock loop (PLL) clock multiplier. It is from 10MHz to 133MHz operating frequency designed to address high-speed clock distribution and multiplication applica- Distributes one clock input to two banks of four outputs tions. The zero delay is achieved by aligning the phase between the incoming Separate output enable for each output bank clock and the output clock, operable within the range of 10 to 133MHz. External feedback (FBK) pin is used to synchronize the outputs The IDT2308 has two banks of four outputs each that are controlled via two to the clock input select addresses. By proper selection of input addresses, both banks can be Output Skew <200 ps put in tri-state mode. In test mode, the PLL is turned off, and the input clock Low jitter <200 ps cycle-to-cycle directly drives the outputs for system testing purposes. In the absence of an 1x, 2x, 4x output options (see table): input clock, the IDT2308 enters power down, and the outputs are tri-stated. In IDT2308-1 1x this mode, the device will draw less than 25 A. IDT2308-2 1x, 2x The IDT2308 is available in six unique configurations for both pre- IDT2308-3 2x, 4x scaling and multiplication of the Input REF Clock. (See available options IDT2308-4 2x table.) IDT2308-1H, -2H, and -5H for High Drive The PLL is closed externally to provide more flexibility by allowing the user No external RC network required to control the delay between the input clock and the outputs. Operates at 3.3V VDD The IDT2308 is characterized for both Industrial and Commercial operation. Available in SOIC and TSSOP packages FUNCTIONAL BLOCK DIAGRAM (-3, -4) 16 FBK 2 2 PLL CLKA1 1 REF 2 (-5) 3 CLKA2 14 CLKA3 15 CLKA4 8 S2 Control 9 Logic S1 2 (-2, -3) 6 CLKB1 7 CLKB2 10 CLKB3 11 CLKB4 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES OCTOBER 2016 1 c 2016 Integrated Device Technology, Inc. DSC 5173/12IDT2308 3.3V ZERO DELAY CLOCK MULTIPLIER COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES (1) PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS Symbol Rating Max. Unit VDD Supply Voltage Range 0.5 to +4.6 V (2) VI Input Voltage Range (REF) 0.5 to +5.5 V 1 16 REF FBK VI Input Voltage Range 0.5 to V 2 15 CLKA1 CLKA4 (except REF) VDD+0.5 3 14 IIK (VI < 0) Input Clamp Current 50 mA CLKA2 CLKA3 IOK Terminal Voltage with Respect 50 mA 4 13 VDD VDD (VO < 0 or VO > VDD) to GND (inputs VIH 2.5, VIL 2.5) 5 12 GND GND IO Continuous Output Current 50 mA 6 (VO = 0 to VDD) CLKB1 CLKB4 11 VDD or GND Continuous Current 100 mA 7 CLKB2 10 CLKB3 TA = 55C Maximum Power Dissipation 0.7 W 8 (3) 9 (in still air) S2 S1 TSTG Storage Temperature Range 65 to +150 C Operating Commercial Temperature 0 to +70 C Temperature Range SOIC/ TSSOP TOP VIEW Operating Industrial Temperature -40 to +85 C Temperature Range NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum PIN DESCRIPTION rating conditions for extended periods may affect reliability. 2. The input and output negative-voltage ratings may be exceeded if the input and output Pin Number Functional Description clamp-current ratings are observed. 3. The maximum package power dissipation is calculated using a junction temperature REF 1 Input Reference Clock, 5 Volt Tolerant Input (1) of 150C and a board trace length of 750 mils. CLKA1 2 Clock Output for Bank A (1) CLKA2 3 Clock Output for Bank A VDD 4 3.3V Supply GND 5 Ground (1) CLKB1 6 Clock Output for Bank B APPLICATIONS: (1) CLKB2 7 Clock Output for Bank B SDRAM (2) S2 8 Select Input, Bit 2 Telecom (2) Datacom S1 9 Select Input, Bit 1 PC Motherboards/Workstations (1) CLKB3 10 Clock Output for Bank B Critical Path Delay Designs (1) CLKB4 11 Clock Output for Bank B GND 12 Ground VDD 13 3.3V Supply (1) CLKA3 14 Clock Output for Bank A (1) CLKA4 15 Clock Output for Bank A FBK 16 PLL Feedback Input NOTES: 1. Weak pull down on all outputs. 2. Weak pull ups on these inputs. 2