Datasheet Cover S128 Microcontroller Group Datasheet Renesas Synergy Platform Synergy Microcontrollers S1 Series The integrated module for Digital Addressable Lighting Interface (DALI) communications is designed for compliance to IEC 62386 version 2 (DALI 2) when used with suitable software and hardware. All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp. without notice. Please review the latest information published by Renesas Electronics Corp. through various means, including the Renesas Electronics Corp. website (Features S128 Microcontroller Group Datasheet Ultra low power 32-MHz Arm Cortex -M0+ core, up to 256-KB code flash memory, 24-KB SRAM, Digital Addressable Lighting Interface, Capacitive Touch Sensing Unit, 14-bit A/D Converter, 8-bit D/A Converter, security and safety features. FeaturesFeatures Arm Cortex-M0+ Core System and Power Management Low power modes Arm v6-M architecture Realtime clock (RTC) Maximum operating frequency: 32 MHz Event Link Controller (ELC) Arm Memory Protection Unit (Arm MPU) with 8 regions Data Transfer Controller (DTC) Debug and Trace: DWT, BPU, CoreSight MTB-M0+ Key Interrupt Function (KINT) CoreSight Debug Port: SW-DP Power-on reset Memory Low Voltage Detection (LVD) with voltage settings Up to 256-KB code flash memory Security and Encryption 4-KB data flash memory (100,000 erase/write cycles) AES128/256 Up to 24-KB SRAM True Random Number Generator (TRNG) Memory protection units 128-bit unique ID Human Machine Interface (HMI) Capacitive Touch Sensing Unit (CTSU) Connectivity USB 2.0 Full-Speed (USBFS) module Multiple Clock Sources - On-chip transceiver with voltage regulator Main clock oscillator (MOSC) - Compliant with USB Battery Charging Specification 1.2 (1 to 20 MHz when VCC = 2.4 to 5.5 V) Serial Communications Interface (SCI) 3 (1 to 8 MHz when VCC = 1.8 to 5.5 V) - UART (1 to 4 MHz when VCC = 1.6 to 5.5 V) - Simple IIC Sub-clock oscillator (SOSC) (32.768 kHz) - Simple SPI High-speed on-chip oscillator (HOCO) Serial Peripheral Interface (SPI) 2 (24, 32, 48, 64 MHz when VCC = 2.4 to 5.5 V) 2 I C bus interface (IIC) 2 (24, 32, 48 MHz when VCC = 1.8 to 5.5 V) Controller Area Network (CAN) module (24, 32 MHz when VCC = 1.6 to 5.5 V) Digital Addressable Lighting Interface (DALI) Middle-speed on-chip oscillator (MOCO) (8 MHz) Low-speed on-chip oscillator (LOCO) (32.768 kHz) Analog IWDT-dedicated on-chip oscillator (15 kHz) 14-bit A/D Converter (ADC14) Clock trim function for HOCO/MOCO/LOCO 8-bit D/A Converter (DAC8) 3 Clock out support High-Speed Analog Comparator (ACMPHS) 3 Low-Power Analog Comparator (ACMPLP) 2 General Purpose I/O Ports Operational Amplifier (OPAMP) 4 Up to 53 input/output pins Temperature Sensor (TSN) - Up to 3 CMOS input - Up to 50 CMOS input/output Timers - Up to 5V tolerant input/output General PWM Timer 32-bit (GPT32) - Up to 2 high current (20 mA) General PWM Timer 16-bit High Resolution (GPT16H) 3 General PWM Timer 16-bit (GPT16) 3 Operating Voltage Asynchronous General-Purpose Timer (AGT) 2 VCC: 1.6 to 5.5 V Watchdog Timer (WDT) Operating Temperature and Packages Safety Ta = -40C to +85C Error Correction Code (ECC) in SRAM - 36-pin LGA (4 mm 4 mm, 0.5 mm pitch) SRAM parity error check Ta = -40C to +105C Flash area protection - 64-pin LQFP (10 mm 10 mm, 0.5 mm pitch) ADC self-diagnosis function - 48-pin LQFP (7 mm 7 mm, 0.5 mm pitch) Clock Frequency Accuracy Measurement Circuit (CAC) - 32-pin LQFP (7 mm 7 mm, 0.8 mm pitch) Cyclic Redundancy Check (CRC) calculator - 48-pin QFN (7 mm 7 mm, 0.5 mm pitch) Data Operation Circuit (DOC) - 32-pin QFN (5 mm 5 mm, 0.5 mm pitch) Port Output Enable for GPT (POEG) Independent Watchdog Timer (IWDT) GPIO readback level detection Register write protection Main oscillator stop detection Illegal memory access R01DS0309EU0110 Rev.1.10 Page 2 of 107 Nov 28, 2018