Q STRIP COAX 14 Gbps CABLE ASSEMBLIES (0.50 mm) .0197 & (0.80 mm) .0315 PITCH HQCD/EQCD SERIES HQCD NO. OF POSITIONS WIRE END END WIRING END SERIES Mates: - PER ROW - LENGTH - NO. 1 - NO. 2 - OPTION - OPTIONS QTH, QSH Leave blank for Specify EQCD HQCD 030, 060, 090 XX.XX 1 no Screw Mount END = (0.50 mm) (HQCD Series) = Wire Length = Pin 1 to Mates: & Retention .0197 pitch in Inches ASSEMBLIES Pin 1 QTE, QSE End Option (43.7 mm) from chart 020, 040, 060 01.72 EQCD (EQCD Series) 2 F minimum = (0.80 mm) = Pin 1 to = Screw Mount SPECIFICATIONS .0315 pitch Pin 2 End No. 1 only (Not available Cable: 3 with XPX 38 AWG micro coax ribbon = Pin 1 to options) Signal Routing: Second to OAL = Wire Length + (24.13) .950 50 W Single-Ended Last Pin S Overall Length: = Screw Mount (95.3 mm) 03.75 to 4 End No. 2 only (1 m) 40 standard Wire Length (1.27) .050 = Pin 1 to Cable Flexing Life: Last Pin >10,000 cycles B Cable Bending Radius: = Screw Mount <2.5mm Both Ends Plating: (Not available Au over 50 (1.27 m) Ni with XPX Current Rating: options) EQCD = 500 mA per pin HQCD = 300 mA per pin 1 (6 adjacent pins powered) = End No. 1 Cable Propagation Delay: Screw Mount. 4.79 nsec/meter End No. 2 Operating Temp Range: Retention Pin -25 C to +105 C or Socket Unmating Force (-RT1 option): -RT1 option increases 2 unmating force up to 50% END NO. 1 END NO. 2 = End No. 1 (STL SHOWN) (STR SHOWN) Retention Pin or Socket. End No. 2 Screw Mount Option END 1 or EDGE MOUNT END 2 Terminal, Edge Mount, Notch Up TEU TED Terminal, Edge Mount, Notch Down END 1 or SURFACE MOUNT SEU Socket, Edge Mount, Notch Up END 2 SED Socket, Edge Mount, Notch Down TTR Terminal, Top Mount, Notch Right TTL Terminal, Top Mount, Notch Left END1 PANEL MOUNT ONLY TBR Terminal, Bottom Mount, Notch Right TPU Terminal, Panel Mount, Notch Up TBL Terminal, Bottom Mount, Notch Left Notes: Cable lengths longer than STR Socket, Top Mount, Notch Right 40.00 (1 meter) are not TPD Terminal, Panel Mount, Notch Down supported with S.I. test data. STL Socket, Top Mount, Notch Left Design your full cable SPU Socket, Panel Mount, Notch Up assembly with Samtecs SBR Socket, Bottom Mount, Notch Right High-Speed Cable Builder at www.samtec.com/cablebuilder SPD Socket, Panel Mount, Notch Down SBL Socket, Bottom Mount, Notch Left This Series is non-standard, non-returnable. F-221 (Rev 17MAR21) samtec.com HQCD or samtec.com EQCD Unless otherwise approved in writing by Samtec, all parts and components are designed and built according to Samtecs specifications which are subject to change without notice.X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Ribbon Cables / IDC Cables category: Click to view products by Samtec manufacturer: Other Similar products are found below : FSK-12A AWG28-10G EHJ3C EHJ4C cab-LVDV-PWR-10-15 FSP-25A 3365/15 (100FT) cab-LVDV-DAT-34-15 49635-C62-S2 1-3636- 600-5204 92315-1408 426171120-3 3625/08 (100M) 0044704 2-1589735-3 JSM015PP2DCC23N 92301-0283 ACL-eSSI-2 92301-0718 MMSDT-06-20-S-05.5-D-K-LDX IDD-04-G NM-2J2-051-PS1-JJAB 1700/14SF (100FT) 1700/26SF (100FT) 1700/34SF (100FT) 3801/09 (100FT) 119-885 DS1057-09A282R-30.5 DS1057-12A282R-30.5 DS1057-14A282R-76.5 DS1057-20A282R-76.5 DS1057-30A282R-76.5 DS1057-34A282R-76.5 DS1057-40A282R-76.5 DS1057-60A282R-76.5 DS1057-64A282R-76.5 DS1058-08M28-30.5 DS1058-30M28-30.5 3750/10 (100FT) 0015712 0015905 S30109 11203 11223 11243 11262 0037147 0022512 0022412 0022416