M24SR02-YMN6T/2 STMicroelectronics

M24SR02-Y Dynamic NFC/RFID tag IC with 2-Kbit EEPROM, NFC Forum Type 4 Tag and IC interface Datasheet - production data Package 8-lead small-outline package (SO8) ECOPACK2 TSSOP8 ECOPACK2 UFDFPN8 SO8 TSSOP8 UFDFPN8 ECOPACK2 Digital pad GPO: configurable general purpose output RF disable: activation/deactivation of RF commands Wafer Temperature range Features From - 40 C up to 85 C 2 I C interface Description 2 Two-wire I C serial interface supports M24SR02-Y belongs to the ST25 family, which 1 MHz protocol includes all STMicroelectronics NFC/RFID tag Single supply voltage: 2.7 V to 5.5 V and reader products. Contactless interface The M24SR02-Y device is a dynamic NFC/RFID tag IC with a dual interface embedding an NFC Forum Type 4 Tag 2 EEPROM. It can be operated from an I C ISO/IEC 14443 Type A interface or by a 13.56 MHz RFID reader or from 106 Kbps data rate an NFC phone. Internal tuning capacitance: 25 pF 2 The I C interface uses a two-wire serial interface, consisting of a bidirectional data line and a clock Memory 2 line. It behaves as a slave in the I C protocol. 256-byte (2-kbit) EEPROM The RF protocol is compatible with ISO/IEC Support of NDEF data structure 14443 Type A and NFC Forum Type 4 Tag. Data retention: 200 years Write endurance: 1 million cycles at 25 C 600 k cycles at 85 C Read: up to 246 bytes in a single command Write: up to 246 bytes in a single command 7-byte unique identifier (UID) 128-bit passwords protection April 2019 DS9985 Rev 12 1/88 This is information on a product in full production. www.st.comContents M24SR02-Y Contents 1 Functional description . 9 1.1 Functional modes . 10 1.1.1 I2C mode 10 1.1.2 Tag mode 10 1.1.3 Dual interface mode 11 2 Description of signals . 12 2.1 Serial clock (SCL) . 12 2.2 Serial data (SDA) . 12 2.3 Antenna coil (AC0, AC1) . 12 2.4 Ground (VSS) 12 2.5 Supply voltage (V ) 12 CC 2.5.1 Operating supply voltage V CC . 12 2.5.2 Power-up conditions . 13 2.5.3 Device reset in IC mode 13 2.5.4 Power-down conditions . 13 2.6 RF disable 13 2.7 General purpose output (GPO) 13 2.7.1 Session Open configuration (GPO field = 0xX1 or 0x1X) . 14 2.7.2 WIP Writing in Progress configuration (GPO field = 0xX2 or 0x2X) . 15 2 2.7.3 I C answer ready configuration (GPO field = 0xX3) . 16 2.7.4 MIP NDEF Message writing in Progress configuration (GPO field = 0x3X) . 17 2.7.5 INT interrupt configuration (GPO field = 0xX4 or 0x4X) . 18 2.7.6 State control configuration (GPO field = 0xX5 or 0x5X) . 19 2.7.7 RF busy configuration (GPO field = 0x6X) . 20 3 M24SR02-Y memory management . 21 3.1 Memory structure . 21 3.1.1 File identifier . 21 3.1.2 CC file layout . 21 3.1.3 NDEF file layout . 22 3.1.4 System file layout 23 3.2 Read and write access rights to the memory 25 2/88 DS9985 Rev 12