M24SR04-YMC6T/2 STMicroelectronics

M24SR04-Y M24SR04-G Dynamic NFC/RFID tag IC with 4-Kbit EEPROM, NFC Forum Type 4 Tag and IC interface Datasheet - production data 7 bytes unique identifier (UID) 128 bits passwords protection Package TSSOP8 UFDFPN8 SO8 8-lead small-outline package (SO8) (DW) (MC) (MN) ECOPACK2 TSSOP8 ECOPACK2 UFDFPN8 ECOPACK2 Digital pad GPO: configurable General Purpose Output Wafer RF disable: activation/deactivation of RF commands Features Temperature range 2 I C interface From - 40 C up to 85 C 2 Two-wire I C serial interface supports 1 MHz protocol Description Single supply voltage: M24SR04 belongs to the ST25 family which 2.7 V to 5.5 V for grade Y includes all STMicroelectronics NFC/RFID tag and 2.4 V to 5.5 V for grade G (Limited reader products. temperature range -25 to 85 C) The M24SR04 devices is a dynamic NFC/RFID tag IC with a dual interface. It embeds an Contactless interface 2 EEPROM memory. It can be operated from an I C NFC Forum Type 4 Tag interface or by a 13.56 MHz RFID reader or an ISO/IEC 14443 Type A NFC phone. 106 Kbps data rate 2 The I C interface uses a two-wire serial interface, Internal tuning capacitance: 25 pF consisting of a bidirectional data line and a clock 2 line. It behaves as a slave in the I C protocol. Memory The RF protocol is compatible with ISO/IEC 512-byte (4-kbit) EEPROM 14443 Type A and NFC Forum Type 4 Tag. Support of NDEF data structure Data retention: 200 years Write cycle endurance: 1 million Write cycles at 25 C 600k Write cycles at 85 C Read up to 246 bytes in a single command Write up to 246 bytes in a single command September 2017 DocID024754 Rev 16 1/89 This is information on a product in full production. www.st.comContents M24SR04-Y M24SR04-G Contents 1 Functional description . 9 1.1 Functional modes . 10 1.1.1 I2C mode 10 1.1.2 Tag mode 10 1.1.3 Dual interface mode 11 2 Signal descriptions . 12 2.1 Serial clock (SCL) . 12 2.2 Serial data (SDA) . 12 2.3 Antenna coil (AC0, AC1) . 12 2.4 Ground (VSS) 12 2.5 Supply voltage (V ) 12 CC 2.5.1 Operating supply voltage V CC . 12 2.5.2 Power-up conditions . 13 2.5.3 Device reset in IC mode 13 2.5.4 Power-down conditions . 13 2.6 RF disable 13 2.7 General purpose output (GPO) 13 2.7.1 Session Open configuration (GPO field = 0xX1 or 0x1X) . 14 2.7.2 WIP Writing in Progress configuration (GPO field = 0xX2 or 0x2X) . 15 2 2.7.3 I C answer ready configuration (GPO field = 0xX3) . 16 2.7.4 MIP NDEF Message writing in Progress configuration (GPO field = 0x3X) . 17 2.7.5 INT Interrupt configuration (GPO field = 0xX4 or 0x4X) 18 2.7.6 State Control configuration (GPO field = 0xX5 or 0x5X) 19 2.7.7 RF busy configuration (GPO field = 0x6X) . 20 3 M24SR04 memory management 21 3.1 Memory structure . 21 3.1.1 File identifier . 21 3.1.2 CC file layout . 21 3.1.3 NDEF file layout . 22 3.1.4 System file layout 23 3.2 Read and write access rights to the memory 25 2/89 DocID024754 Rev 16