.2314 3)/. (%%3 )& & & &- )&+* & ) +,) & (( +)* %5 ITEM NO. PART NO. DESCRIPTION QTY 1 6906711 PLATE, Base 1 2 6906722 MOUNT, Base 1 3 4210024 SCREW, Btn Hd Cap, 3/816 x .500 in. L 3 4 3210006 SCREW, Skt Hd Cap, No. 1032 x .625 in. L 2 5 6906732 BRACKET, HoldDown 1 6 2210007 SCREW, Skt Hd Cap, No. 832 x .500 in. L 2 7 6906741 STOP, Rear 2 8 210094 SETSCREW, Skt, Slflkg, 1/420 x .375 in. L 1 9 6904991 RAM 1 10 Deleted 11 6949251* BRACKET ASSY, Vertical Reel REF 12 6949282 BRACKET, LH Stock Guide 1 13 4702681 GUIDE, Stock 1 14 3210001 SCREW, Skt Hd Cap, No. 832 x 1.00 in. L 4 15 277083 KNOB, Thumbscrew 2 16 210222 NUT, Slflkg, No. 832 1 17 4557441 SHROUD, End Feed 1 18 4557451 GUARD, End Feed 1 19 1218993 WASHER, Flat, No. 8 12 20 210186 NUT, Hex, No. 832 7 21 7224680 SCREW, Bdg Hd, No. 832 x .375 in. L 5 22 7224683 SCREW, Bdg Hd, No. 832 x .750 in. L 1 23 222801 SPRING, Compression 1 24 4557481 SHROUD, Side Feed 1 25 4557491 GUARD, Side Feed 1 26 3210024 SCREW, Btn Hd Cap, 1/420 x .625 in. L 1 27 218993 WASHER, Flat, 1/4 in. 1 *Refer to Customer Manual 4095128 for the detailed parts breakdown of assembly and related parts.. Figure 1 7 / ,% 31/.) 2 /10/1 3)/. 11)2 41 ()2 /.31/,,% / 4-%.3)224 *% 33/ ( .% /& ,, .3%1. 3)/. , )(32 %2%15% /1, 3%231%5)2)/ %)/. , 423/-%1 %15) % ,// . 7 / ,% 31/.) 2 1%31 %- 1+2 5)2)3/4162)3% 3... +/ +) * % 1 %- 1+ 3(%101/ 4 32 ,//2 . /-0 .7. -%242% 1%3(%01/0%137/&3(%)11%20% 3)5%/6.%12 &%( &% )( % 3. Remove the two base mount screws and washers form frame and install the base mount These conversion kits are used to modify supplied in the kit. Adjust height of the base mount AMPOLECTRIC Model K Terminating Machines to as low as possible in accordance with the machine accept miniature quickchange applicators. Kit No. manual. 6906752 is required for all endfeed and those sidefeed applicators that receive the strip terminals 4. Handcycle in accordance with the machine in a horizontal position. Refer to the exploded view manual until the toggle link is at its lowest position. and parts list in Figure 1 to make sure you have all 5. Remove the arm retaining plate by removing the the parts required for the conversion. Kit No. 6906752 plus Kit No. 6926131 are required for four screws. those sidefeed applicators that receive the strip 6. Loosen the setscrew in the ram, and then pivot terminals in a vertical position. the toggle link toward the front of the machine and slide out the toggle link pin to remove the ram. +) ).-- , (,-+. - )(, 0 + + + ( , -) ( 1 & - ( ( -)- 7. Lubricate the four sides of the new ram, , ( * +-, ( ,, & , + +-) supplied in the kit, as specified in the machine .,-) + (. & manual. Read the following instructions carefully before and 8. Pivot the toggle link forward and install the new during the installation of the conversion kits on the ram with the toggle link pin removed in Step 6. machine. Pivot the ram back into position and tighten the setscrew provided in the kit. 9. Install the ram retaining plate with the four screws removed in Step 6. Before starting installation of the conversion kits, remove and store mechanical feed arm or air feed 10. Handcycle the machine to the rest position operation arm from feed mechanism shaft by (top dead center). loosening or removing clamp screws. 11. All parts removed for conversion, and any .+ (,- && - )() - )(/ +, )(% - +- ( unused parts of the kit, should be retained and * +-, ( ,, & , + )/ ( stored. - +*& (,-)+ )++ - ( )+ (,- && - )( ) - % - ,% - ,()-+ ) ( )+ ) &, ) & %() ) &% ( ( , This kit, in addition to Kit 6906752, is required ONLY - - & -+ &*)0 +-)- for side feed applicators that receive strip terminals in ( , 1*.&& - *& +)- a vertical position. + *- & 1. Lay out the machine frame for holes as shown in Figure 3. ) & %() ) &% 2. Drill two size G holes, and thread with 5/1618 UNC2B tap. For installation of this kit, the machine must be equipped with the proper vertical reel bracket 3. Assemble the reel support as shown and install assembly (Part No. 6949251). For information on the machine with the two screws supplied in the pertaining to this assembly, refer to Customer Manual kit. 4095128. 1. The lefthand stock guide is required ONLY when using sidefeed applicators. With guide installed on the bracket, attach the bracket to the it is NECESSARY for all miniature quickchange vertical reel bracket assembly with two screws applicators, when used in an AMPOLECTRIC capped with knurled knobs, as shown. machine, to be equipped with the CORRECT feed 2. To guide the terminal strip properly into cam as listed on the applicator parts list (log) supplied endfeed applicators, it is necessary that the with the applicator. CHECK the feed cam, and if righthand stock guide bracket be lowered by necessary, replace it as described in the applicator using the UPPER hold in the vertical support for instructions supplied with the applicator. Retain all the left screw, as shown. parts that are removed.