8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. 3 RELEASED PER E090033 AR 01/09/09 REJH 4 REVISED PER E092035 JS 11/16/09 REJH F F 5 REDRAWN PER E100871 DCS 07/01/10 KUK 6 REVISED PER E111266 VSS 12/22/11 REJH <> SEE NOTE 6 .16 30 DRILL THRU 7 REVISED PER E120702 ZMB 07/31/12 REJH (12) PL. <> ( .1285 ) SEE NOTE 5 (6) PL010 .90 MATL TO BE <> REMOVED E E FULL R (6) PL. 2.000 2.220 <> D D .11 .650 .190 <> <> .100 .49 1.300 <> <> <> -A- .005 2.28 C C <> .910 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. 2. REMOVE ALL BURRS AND SHARP EDGES. DRAWN BY DATE SWD VICOR 3. CLEAR FINISH, RoHS COMPLAINT PER CST-0001, LATEST REVISION PER <> Robert Hickey 07/01/2010 A)CHROMIUM FREE, OR B)TRIVALENT CHROMIUM IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASSS 1A OR 3. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES HS LONG .9H LF THRU HL TOLERANCES ARE: DECIMALS ANGLES 4. <> DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 5. DIMENSIONS APPLIES AT SURFACE -A- (2) PL. SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. 7. DIMENSIONS ARE INCHES ONLY. C 67131 30182 7 2:1 2 SCALE SHEET OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F A SEE DETAIL 3 1.5 EACH SIDE OF VERT E E 1.756 R.018 (2) PL910 R.035 .023 .036 .031 .215 .200 .040 .080 D D .110 (14) PL. * .084 * .087 R.010 (2) PL. (5) PL. (2) PL. R.035 (18) PL. * .178 (2) PL. R.030 (33) PL. * .174 .372 (6) PL752 C C +.020 .007 2.220 -.000 (2) PL191 DETAIL A SCALE 8 : 1 PROFILE COMMON FOR C B B L 30123 30181 30189 30182 30188 * .087 NOTES: 1. MATERIAL: ALUMINUM 6063-T5 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. DRAWN BY DATE SWD VICOR 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. Robert Hickey 07/01/2010 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. WORKMANSHIP STANDARDS WS-0004, WS-0006, AND WS0007 APPLY TO THIS PART. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM 6. DIMENSIONS ARE INCHES ONLY. HS LONG .9H LF THRU HL TOLERANCES ARE: DECIMALS ANGLES A A EXTRUSION X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30182 7 1:1 2 SCALE SHEET OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1