CRCW08053K90JNEAIF

D/CRCW-IF e3 www.vishay.com Vishay Pulse Proof Thick Film Chip Resistors FEATURES High pulse performance, up to 10 kW Stability R/R 1 % for 1000 h at 70 C AEC-Q200 qualified Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 STANDARD ELECTRICAL SPECIFICATIONS LIMITING POWER ELEMENT CASE CASE TEMPERATURE RESISTANCE RATING VOLTAGE TOLERANCE TYPE SIZE SIZE COEFFICIENT RANGE SERIES P U % 70 max. IMPERIAL METRIC ppm/K W AC /DC RMS V 5 D10/CRCW0402-IF 0402 RR1005M 0.063 50 200 1.0 to 100K E24 10 5 D11/CRCW0603-IF 0603 RR1608M 0.10 75 200 1.0 to 100K E24 10 5 D12/CRCW0805-IF 0805 RR2012M 0.125 150 200 1.0 to 100K E24 10 5 D25/CRCW1206-IF 1206 RR3216M 0.25 200 200 1.0 to 100K E24 10 5 CRCW1210-IF 1210 RR3225M 0.50 200 200 1.0 to 100K E24 10 5 CRCW2010-IF 2010 RR5025M 0.75 400 200 1.0 to 100K E24 10 5 CRCW2512-IF 2512 RR6332M 1.0 500 200 1.0 to 100K E24 10 Notes These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and permissible film temperature. However, the resistance typically increase due to the resistors film temperature over operating time, generally known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time. Marking: See data sheet Surface Mount Resistor Marking (document number 20020). Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS D10/ D11/ D12/ D25/ PARAMETER UNIT CRCW1210-IF CRCW2010-IF CRCW2512-IF CRCW0402-IF CRCW0603-IF CRCW0805-IF CRCW1206-IF Rated dissipation W 0.063 0.1 0.125 0.25 0.5 0.75 1.0 (1) P 70 Operating voltage V 50 75 150 200 200 400 500 U AC /DC max. RMS Insulation voltage V 75 100 200 300 300 300 300 U (1 min) ins 9 Insulation resistance > 10 Operating temperature C -55 to +155 range -1 -9 Failure rate h < 0.1 x 10 Mass mg 0.65 2 5.5 10 16 25.5 40.5 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printe-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 C is not exceeded. Revision: 17-Mar-15 Document Number: 20024 1 For technical questions, contact: thickfilmchip vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 D/CRCW-IF e3 www.vishay.com Vishay PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRCW08051R00JNEAIF CR C W 0805 1 R 00JEN AI F TYPE VALUE TOLERANCE TCR PACKAGING SPECIAL EA, EB, CRCW0402 R = Decimal J = 5 % N = 200 ppm/K Up to 2 digits EC, ED, CRCW0603 K = Thousand K = 10 % IF = Pulse proof EE, EF, CRCW0805 EG, EH, CRCW1206 EI, EL CRCW1210 CRCW2010 CRCW2512 Product Description: D12/CRCW0805-IF 200 1R0 5 % ET1 e3 D12/CRCW0805-IF 200 1R0 5 % ET1 e3 TYPE TCR RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE D10/CRCW0402-IF 200 ppm/K 1R0 = 1 5 % ET1, ET2, e3 = Pure tin D11/CRCW0603-IF 10K = 10 k 10 % ET3, ET4, termination finish D12/CRCW0805-IF ET5, ET6, D25/CRCW1206-IF ET7, ET8, CRCW1210-IF ET9, EF4, CRCW2010-IF E02, E67, CRCW2512-IF E82 PACKAGING TYPE CODE QUANTITY CARRIER TAPE WIDTH PITCH REEL DIAMETER ED = ET7 10 000 180 mm/7 D10/CRCW0402-IF 8 mm 2 mm EE = EF4 50 000 330 mm/13 EI = ET2 5000 180 mm/7 ED = ET3 10 000 180 mm/7 8 mm 2 mm EL = ET4 20 000 285 mm/11.25 D11/CRCW0603-IF EE = ET8 50 000 330 mm/13 EA = ET1 5000 180 mm/7 EB = ET5 10 000 8 mm 4 mm 285 mm/11.25 Paper tape acc. to EC = ET6 20 000 330 mm/13 IEC 60286-3 EA = ET1 5000 180 mm/7 Type 1a D12/CRCW0805-IF EB = ET5 10 000 8 mm 4 mm 285 mm/11.25 EC = ET6 20 000 330 mm/13 EA = ET1 5000 180 mm/7 D25/CRCW1206-IF EB = ET5 10 000 8 mm 4 mm 285 mm/11.25 EC = ET6 20 000 330 mm/13 EA = ET1 5000 180 mm/7 CRCW1210-IF EB = ET5 10 000 8 mm 4 mm 285 mm/11.25 EC = ET6 20 000 330 mm/13 CRCW2010-IF EF = E02 4000 Pressed tape 12 mm 4 mm 180 mm/7 acc. to EG = E67 2000 8 mm IEC 60286-3 CRCW2512-IF 12 mm 180 mm/7 EH = E82 4000 4 mm Type 1b Revision: 17-Mar-15 Document Number: 20024 2 For technical questions, contact: thickfilmchip vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000