TSOP582.., TSOP584.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against optical noise 1 Insensitive to supply voltage ripple and noise 22 Material categorization: 33 19026 for definitions of compliance please see www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS DESCRIPTION Models These products are miniaturized IR receiver modules for Available infrared remote control systems. A PIN diode and a preamplifier are assembled on a leadframe, the epoxy MECHANICAL DATA package contains an IR filter. Pinning for TSOP582.., TSOP584..: The demodulated output signal can be directly connected to 1 = OUT, 2 = GND, 3 = V S a microprocessor for decoding. The TSOP584.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. They may suppress some data signals if continuously transmitted. The TSOP582.. series devices are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP584.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR LONG BURST REMOTE CONTROLS RECOMMENDED FOR LONG AGC (AGC2) BURST CODES (AGC4) 30 kHz TSOP58230 TSOP58430 33 kHz TSOP58233 TSOP58433 (1)(2)(3) 36 kHz TSOP58236 TSOP58436 Carrier frequency (4)(5) 38 kHz TSOP58238 TSOP58438 40 kHz TSOP58240 TSOP58440 (6)(7) 56 kHz TSOP58256 TSOP58456 Package Minicast Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Rev. 1.7, 26-Sep-2018 Document Number: 82461 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP582.., TSOP584.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833 14 17170-11 R 1 3 Transmitter IR receiver with V + V 33 k S S TSALxxxx C 1 1 C Band Demo- OUT Input AGC pass dulator V O GND GND 2 PIN Control circuit R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to 5.5 V O Voltage at output to supply V - V -0.3 to (V + 0.3) V S O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, IR diode TSAL6200, v Transmission distance d- 18 - m I = 50 mA, test signal see Fig. 1 F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E -0.2 0.4 mW/m e min. t - 5/f < t < t + 6/f test signal see Fig. 1 pi o po pi o, 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - deg 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Optical Test Signal 1.0 E e (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) F 0 Output Pulse Width 0.9 0.8 Input Burst Length 0.7 t 0.6 t * pi 0.5 T 0.4 * t 10/f is recommended for optimal function pi 0 0.3 Output Signal 16110 V O 0.2 = 950 nm, 1) 7/f < t < 15/f 0.1 Optical Test Signal, Fig.1 V 0 d 0 OH 2) t - 5/f < t < t + 6/f pi 0 po pi 0 0 2 3 4 0.1 1 10 10 10 10 V OL 1) 2) 2 t t t d po E - Irradiance (mW/m ) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.7, 26-Sep-2018 Document Number: 82461 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit