JTL6048S15

DS JTL60 061021.qxp JTL60 06/10/2021 11:19 Page 1 DC-DC Converter JTL60 Series XPPower 60 Watts Single and Dual Outputs xxx Series Wide 4:1 Input Range 2 x 1 Footprint -40 C to +85 C Operation Full Load at 50 C Ambient 1600 VDC Isolation Output Trim 10% Remote On/Off 3 Year Warranty Dimensions: JTL60: 2.0 x 1.0 x 0.45 (50.8 x 25.4 x 11.5 mm) Models & Ratings (1) Input Current Input Output Output Max. (3) OVP setting Efficiency Model Number (2) Voltage Voltage Current No Load Full Load capacitive load 5.0 V 12.0 A 25 mA 2705 mA 6.2 V 92% 30,000 F JTL6024S05 12.0 V 5.0 A 25 mA 2705 mA 15.0 V 92% 5850 F JTL6024S12 9-36 V 15.0 V 4.0 A 25 mA 2690 mA 20.0 V 93% 3900 F JTL6024S15 12.0 V 2.5 A 40 mA 2750 mA 15.0 V 91% 3900 F JTL6024D12 15.0 V 2.0 A 50 mA 2730 mA 20.0 V 91% 2400 F JTL6024D15 5 V 12.0 A 25 mA 1345 mA 6.2 V 93% 30,000 F JTL6048S05 12 V 5.0 A 25 mA 1350 mA 15.0 V 92% 5850 F JTL6048S12 18-75 V 15 V 4.0 A 25 mA 1345 mA 20.0 V 93% 3900 F JTL6048S15 12 V 2.5 A 40 mA 1375 mA 15.0 V 91% 3900 F JTL6048D12 15 V 2.0 A 50 mA 1375 mA 20.0 V 91% 2400 F JTL6048D15 Notes 1. Input currents measured at nominal input voltage. 3. Add suffix -HK for optional heatsink 2. Maximum capacitive load is per output. Mechanical Details Optional Heatsink (-HK) 0.40 0.10 0.40 0.45 0.69 0.10 (10.16) (10.16) (2.54) (11.5) (17.6) (2.54) Pin Connections 0.10 4 5 6 (2.54) Pin Single Dual 0.10 Print 1 +Vin +Vin (2.59) Face 2 -Vin -Vin 3 Remote On/Off Remote On/Off 2.0 2.0 (50.8) 4 +Vout +Vout Bottom View (50.8) TOP 5 -Vout Common Dia 6 Trim -Vout 0.04 (1.0) 0.10 (2.54) Notes 1 2 3 1. All dimensions are in inches (mm) 0.10 2. Weight: 0.09 lbs (41.0 g) approx. 0.20 0.24 1.0 (25.4) (2.54) (5.08) 3. Pin diameter: 0.020.002 (0.50.05) (6.0) 4. Pin pitch tolerance: 0.014 (0.35) 0.60 (15.24) Heat-sink 5. Case tolerance: 0.02 (0.5) Thermal Pad Converter www.xppower.com 1DS JTL60 061021.qxp JTL60 06/10/2021 11:19 Page 2 DC-DC Converter JTL60 Series XPPower Input Characteristic Minimum Typical Maximum Units Notes & Conditions 9 36 VDC 24 V nominal Input Voltage Range 18 75 VDC 48 V nominal Input Reflected Ripple Current 20 mA pk-pk Through 11 H inductor and 22 F capacitor 50 VDC for 100 ms 24 V models Input Surge 100 VDC for 100 ms 48 V models Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 5.0 30 VDC See Models and Ratings table Output Trim 10 % See Application Note Initial Set Accuracy 1 % At full load Minimum Load 0 % No minimum load required Line Regulation 0.5 % From minimum to maximum input at full load Load Regulation 0.5/1.0 % From 0% to full load for single/dual output On dual output models, when one output is at 100% load Cross Regulation 5 % and other is varied from 25% load to full load Start Up Time 60 ms Measured using 20 MHz bandwidth and 1.0 F ceramic Ripple & Noise 100 mV pk-pk capacitor Overload Protection 120 140 % Short Circuit Protection Continuous hiccup mode, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ C Overvoltage Protection See Models and Ratings table Output is on if remote on/off (pin 3) is open or high (3-12 VDC) Remote On/Off Output turns off if remote on/off (pin 3) is low (<1.2 VDC max) General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 93 % See Models and Ratings table Isolation: Input to Output 1600 VDC Isolation: Input and output to 1600 VDC Case Switching Frequency 225 kHz 9 Isolation Resistance 10 Isolation Capacitance 2200 pF 3 Power Density 66 W/in Mean Time Between Failure 210 kHrs MIL-HDBK-217F, +25 C GB Weight 0.1 (45.0) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +85 C See Derating Curve Storage Temperature -55 +125 C Case Temperature +115 C Humidity 95 %RH Non-condensing Cooling Natural convection www.xppower.com 2