Kleanium Flux Remover Heavy Duty Aerosol 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: Chemtools Kleanium Flux Remover Heavy Duty Aerosol Product Type: Flux solvent for industrial use. Part Numbers: CT-FRHD-300, -300DB Company Address: Chemtools Pty,. Ltd., PO Box 463, Emu Plains, NSW 2750 Ph: 1300 738 250 EMERGENCY PHONE: Australia: Poisons Information Centre 13 1126 International: Infotrac (708) 918 1900 2. COMPOSITION/INFORMATION ON INGREDIENTS Hazardous components CAS % HSIS TWA HSIS STEL 3 3 propan-2-ol 67-63-0 30 - 60 400ppm 983mg/m 500ppm 1,230mg/m 3 ethanol 107-98-2 30 - 60 1000ppm 1,880 mg/m 3 3 carbon dioxide 124-38-9 <10 5,000ppm 9,000mg/m 30,000ppm 54,000mg/m 3. HAZARDS IDENTIFICATION Hazard Classification: Hazardous Material, Dangerous Goods according to the criteria of SafeWork Australia and the ADG-7 code) Risk Phrases: R11 Highly flammable R22 Harmful if swallowed R36/38 Irritating to eyes and skin. R67 Vapours may cause drowsiness and dizziness. Safety Phrases: S20 When using do not eat or drink S21 When using do not smoke S51 Use only in well ventilated areas. S24/25 Avoid contact with skin and eyes. Relevant routes of exposure: Skin, Inhalation, Eyes Potential Health Effects Inhalation: May cause respiratory tract irritation. High concentrations of vapours may cause headache, fatigue, drowsiness and dizziness. Skin contact: May cause allergic skin reaction. May cause skin irritation. Product has a defatting effect on skin. Prolonged contact may cause dryness of skin. Eye contact: Contact with eyes will cause irritation. Ingestion: Harmful. May cause lung damage if swallowed. 4. FIRST AID MEASURES Inhalation: Remove to fresh air. If symptoms develop and persist, get medical attention. Skin contact: Wash with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if symptoms occur. Eye contact: Check for and remove any contact lenses. Immediately flush with copious amounts of water, preferably, lukewarm water for at least 15 minutes, holding eyelids open all the time. Get medical attention. Ingestion: Do not induce vomiting. Rinse mouth thoroughly. Loosen any tight clothing. Keep individual calm. Obtain medical attention. 5. FIRE-FIGHTING MEASURES Flash point: -4C Cleveland closed cup Autoignition temperature: 425C Flammable/Explosive limits-lower %: 2% Flammable/Explosive limits-upper %: 12% Extinguishing media: Foam, dry chemical or carbon dioxide. Special fire fighting procedures: None Unusual fire or explosion hazards: None Hazardous combustion products: Oxides of carbon. Irritating organic vapours. Keep run-off water out of sewers and water sources. Hazchem Code: 2 Y E 6. ACCIDENTAL RELEASE MEASURES Material Safety Data Sheet info chemtools.com.au Issued by: Chemtools Pty., Ltd., Page 1 of 4 www.chemtools.com.au Kleanium Flux Remover Heavy Duty Aerosol Environmental precautions: Extinguish all ignition sources. Ventilate well. Use approved respirator if air contamination is above accepted level. Prevent product from entering drains or open waters. Clean-up methods: Soak up with inert absorbent. Store in a partly filled, closed container until disposal. 7. HANDLING AND STORAGE Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapour and mist. Wash thoroughly after handling. Storage: For safe storage, store at or below 38C (100F). Keep in a cool, well-ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Incompatible products: Refer to Section 10. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering controls: No specific ventilation requirements noted, but forced ventilation may still be required if concentrations exceed occupational exposure limits. Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Skin protection: Use impermeable gloves and protective clothing as necessary to prevent skin contact. Neoprene gloves. butyl rubber gloves. Natural rubber gloves. Eye/face protection: Safety goggles or safety glasses with side shields. See Section 2 for exposure limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Liquid in aerosol canister Colour: Clear, colourless. Odour: alcoholic. pH: Not available Boiling point/range: >80C. Melting point/range: Not available Specific gravity: 0.78 at 20C. Vapour density: >1 Evaporation rate: Not available Solubility in water: Insoluble. 10. STABILITY AND REACTIVITY Stability: Stable. Hazardous polymerization: Will not occur. Hazardous decomposition products: Oxides of carbon. Incompatibility: Strong oxidizers. Strong reducing agents. Conditions to avoid: SeeHandling and Storag (Section 7) andIncompatibilit (Section 10). 11. TOXICOLOGICAL INFORMATION Product toxicity data: Isopropyl alcohol Oral: LD 5,045 mg/Kg (rat). Skin: LD 12.8g/Kg (rabbit) Inhalation LC : 16,000ppm/8hr 50 50 50 (rat) Investigated as a tumorigen, mutagen, and reproductive effector. Carcinogenic effects: IARC Category 3 Ethanol Acute Oral Toxicity LD (rat) 5500 mg/kg 50 Acute Oral Toxicity LD (rabbit) 4935 mg/kg 50 Acute Inhalation Toxicity LC (rat) 1600 ppm/8hrs 50 Acute Inhalation Toxicity LC (rat) 45000 ppm/2hrs 50 Inhalation Lowest Toxic Concentration (human) 400 ppm Eyes (human): Irritant. There is some indication that this chemical may cause an allergic response in some individuals. No evidence of carcinogenicity was seen in mice. Not regulated as a carcinogen by the USA NTP, WHO IARC monographs, USA OSHA, or USA ACGIH. 12. ECOLOGICAL INFORMATION Ecological information: . Material Safety Data Sheet info chemtools.com.au Issued by: Chemtools Pty., Ltd., Page 2 of 4 www.chemtools.com.au