Description Descos ESD inspection gloves are designed to be worn when handling ESD susceptible items. They are made with dissipative 5 8 (1 x 10 to < 1 x 10 ohms) Thunderon Fibers to reduce charge generation and bond to a grounded operator. Additional silicone free carrier yarn is made with Kevlar Kleen which helps to protect operators hands from cuts on circuit board edges, leads, and other sharp objects. The carrier yarn will also absorb sweat and oils produced by the operators hands to help prevent contamination. The seamless fine gauge knit is designed for all-day wear allowing easy hand movement and a high level of tactile sensitivity. Descos ESD inspection gloves may be laundered and will retain their ESD properties for 30 washings or approximately 1 year. Features 5 8 Dissipative (1 x 10 to < 1 x 10 ohms) Thunderon Fibers Protective Carrier Yarn 5 8 Resistance 1 x 10 to < 1 x 10 ohms tester per ANSI/ESD 5P15.1 Standard Practice for In-Use Resistance Testing of Gloves and Finger Cots Item Size Length* A properly grounded operator can touch a charged 68120 Small 7-3/8 ESD sensitive device and a damaging ESD event *Length is measured from the tip of can occur (Charged Device Model). Increasing the 68121 Medium 7-1/2 the fingers to the bottom of the glove electrical paths contact resistance is one way to 68122 Large 7-3/4 control the speed of the discharge and reduce the possibilities of damage. A good way to accomplish 68123 X-Large 8 this is by wearing static dissipative gloves. Sold in Pairs Per JESD625-A (Revision of EIA-625) paragraph 11.5 Gloves / Finger Cots Glove Laundering When gloves or finger cots are required, only cotton For proper operation, the ESD Gloves must be laundered periodically. Woolite works gloves, antistatic/conductive gloves, or antistatic/ conductive finger cots should be used when handling well. Liquid detergents are better than dry in that there is less caking and frictional Inspection Gloves In Use ESDS ESD sensitive devices. wear. Launder glove in cool or warm water, tumble dry with low heat or hang dry. Machine washing works well if using a standard house machine on gentle cycle. It is not Note: The user must determine the suitability for use of an ESD glove for his particular recommended to launder these gloves in heavy industrial laundry machines as it will lead application. The ESD Association recommends that personnel grounding items should to premature wear. Gloves should be tumbled dry using low heat. DO NOT BLEACH. After not be used in situations where inadvertent exposure to line voltage is possible. The 5 8 laundering, verify Rtt 1 x 10 to < 1 x 10 ohms. user should check with local safety personnel to determine requirements for their particular area. Specifications and procedures subject to change without notice. Operators to be grounded via a wrist strap or ESD flooring-footwear system can test their personnel grounding device while the glove is worn using a regular wrist strap / footwear tester. ESD Inspection Glove DESCO WEST: 3651 WALNUT AVE., CHINO, CA 91710 WEB SITE: Desco.com DATE: PHONE (909) 627-8178 DRAWING NUMBER May DESCO EAST: ONE COLGATE WAY, CANTON, MA 02021-1407 68120 2015 PHONE (781) 821-8370 2015 DESCO INDUSTRIES INC. Employee OwnedX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Antistatic Control Products category: Click to view products by Desco manufacturer: Other Similar products are found below : 13020 13490 13870 13879 13881 13883 13882 14404 2202SP 3039 37061 42470 09060 09857 42516 37059 04563 17252 19691 19695 09037 09826 09813 66070 100816 68101 68103 98132 73741 13868 13485 13457 13245 13468 13420 13332 13205 13135 91070 8031 8523 66085 40931 37081 13080 13215 13806 73749 010-0225 17260