PD2601 IXYS

PD2601 AC Solid State Relays INTEGRATED CIRCUITS DIVISION Description Parameter Rating Units The PD2601 is an AC Solid State Switch using optical AC Operating Voltage 260 V rms coupling with dual power SCR outputs to produce an Load Current 1 A rms alternative to optocoupler and Triac circuits. The On-State Voltage Drop 1.2 V rms PD2601 switches are robust enough to provide a (I =1A ) L rms blocking voltage of up to 600V and max surge P current rating of 20A. In addition, tightly controlled Features zero-cross circuitry ensures switching of AC loads Load Current up to 1A rms without the generation of transients. The input and Blocking Voltages up to 600V P output circuits are optically coupled to provide 3750V Input to Output Isolation rms 3750V of isolation and noise immunity between rms 5mA Sensitivity control and load circuits. As a result the PD2601 Zero-Crossing Detection is well suited for industrial environments where DC Control, AC Output electromagnetic interference would disrupt the Low EMI and RFI Generation operation of electromechanical relays. High Noise Immunity VDE compatible Approvals Flammability Rating UL 94 V-0 UL Recognized Component: UL 508 File E69938 CSA Certified Component: File 043639 Applications Programmable Control Ordering Information Process Control Power Control Panels Part Description Remote Switching PD2601 4-Pin (16-Pin Body) DIP Package (25/Tube) Gas Pump Electronics Contactors Large Relays Pin Configuration Solenoids Motors 1 16 Heaters + LED - LED ZC 10 AC Load 8 AC Load DS-PD2601-R15 1 www.ixysic.comPD2601 INTEGRATED CIRCUITS DIVISION Absolute Maximum Ratings 25C Absolute Maximum Ratings are stress ratings. Stresses in Parameter Min Max Units excess of these ratings can cause permanent damage to Blocking Voltage - 600 V P the device. Functional operation of the device at conditions Reverse Input Voltage - 5 V beyond those indicated in the operational sections of this Input Control Current - 100 mA data sheet is not implied. Peak (10ms) - 1 A 1 Input Power Dissipation - 150 mW Typical values are characteristic of the device at +25C, 2 and are the result of engineering evaluations. They are Total Package Dissipation - 1600 mW provided for information purposes only, and are not part of Isolation Voltage, Input to Output 3750 - V rms the manufacturing testing requirements. Operational Temperature -40 +85 C Storage Temperature -40 +125 C 1 Derate linearly 1.33 mW / C 2 Derate linearly 16.6 mW / C Electrical Characteristics 25C Parameter Conditions Symbol Min Typ Max Units Output Characteristics AC Operating Voltage I =5mA V 20 - 260 V F OP rms Load Current (Continuous) V =120-240VAC I 0.005 - 1 A L L rms Maximum Surge Current t<16ms I - - 20 A PEAK Off-State Leakage Current V =600V I -- 1 mA L DC LEAK On-State Voltage Drop I =1.0A - - - 1.2 V L rms rms Critical Rate of Rise - dV/dt 1000 1200 - V/s Switching Speeds Turn-On t - - 0.5 on I =5mA Cycles F Turn-Off t - - 0.5 off 1 st Zero-Cross Turn-On Voltage 1 half-cycle -2 5 V - Subsequent half-cycle - - 1 V Operating Frequency - - 20 - 500 Hz 2 Load Power Factor for Guaranteed Turn-On - PF 0.25 - - - Capacitance Input-To-Output V =0V, f=1MHz C -3 - pF IO IO Input Characteristics Input Control Current For Normal Environment - -- 5 I mA F For High Noise Environment - - - 10 Input Voltage Drop I =5mA V 0.9 1.2 1.5 V F F Input Dropout Voltage - - 0.8 - - V Reverse Input Current V =5V I - - 10 A R R 1 st Zero Cross 1 half-cycle < 100Hz. 2 Snubber circuits may be required at low power factors. 2 R15 www.ixysic.com