Document Number: IMXRT1015CEC NXP Semiconductors Rev. 3, 08/2021 Data Sheet: Technical Data MIMXRT1015DAF5A MIMXRT1015DAF5B i.MX RT1015 Crossover Processors Data Sheet for Consumer Products Package Information Plastic Package 100-Pin LQFP, 14 x 14 mm, 0.5 mm pitch Ordering Information See Table 1 on page 5 1 i.MX RT1015 introduction The i.MX RT1015 is a processor of i.MX RT family 1. i.MX RT1015 introduction 1 1.1. Features 2 featuring NXPs advanced implementation of the Arm 1.2. Ordering information . 5 Cortex -M7 core, which operates at speeds up to 500 2. Architectural overview . 7 2.1. Block diagram 7 MHz to provide high CPU performance and real-time 3. Modules list . 8 response. 3.1. Special signal considerations . 13 3.2. Recommended connections for unused analog The i.MX RT1015 processor has 128 KB on-chip RAM, interfaces . 14 4. Electrical characteristics 15 which can be flexibly configured as TCM or 4.1. Chip-level conditions 15 general-purpose on-chip RAM. The i.MX RT1015 4.2. System power and clocks 21 integrates advanced power management module with 4.3. I/O parameters 26 4.4. System modules . 32 DCDC and LDO that reduces complexity of external 4.5. External memory interface . 37 power supply and simplifies power sequencing. The 4.6. Audio 43 4.7. Analog . 46 i.MX RT1015 also provides various memory interfaces, 4.8. Communication interfaces 52 including Quad SPI, and a wide range of connectivity 4.9. Timers . 56 interfaces including UART, SPI, I2C, and USB for 5. Boot mode configuration 58 5.1. Boot mode configuration pins . 58 connecting peripherals including Bluetooth, and GPS. 5.2. Boot device interface allocation 58 The i.MX RT1015 also has rich audio features, including 6. Package information and contact assignments . 61 6.1. 14 x 14 mm package information 61 SPDIF and I2S audio interface. Various analog IP 7. Revision history . 68 integration, including ADC, temperature sensor, etc. NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products. 2019-2021 NXP B.V.i.MX RT1015 introduction The i.MX RT1015 is specifically useful for applications such as: Industrial Motor Control Home Appliance Audio IoT 1.1 Features The i.MX RT1015 processors are based on Arm Cortex-M7 Core Platform, which has the following features: Supports single Arm Cortex-M7 with: 16 KB L1 Instruction Cache 16 KB L1 Data Cache Full featured Floating Point Unit (FPU) with support of the VFPv5 architecture Support the Armv7-M Thumb instruction set Integrated MPU, up to 16 individual protection regions Up to 128 KB I-TCM and D-TCM in total Frequency of 500 MHz Cortex M7 CoreSight components integration for debug Frequency of the core, as per Table 9,Operating ranges on page 17. The SoC-level memory system consists of the following additional components: Boot ROM (96 KB) On-chip RAM (128 KB) Configurable RAM size up to 128 KB shared with CM7 TCM External memory interfaces: SPI NOR/NAND FLASH Parallel NOR FLASH with XIP support Single/Dual channel Quad SPI FLASH with XIP support Timers and PWMs: Two General Programmable Timers 4-channel generic 32-bit resolution timer Each support standard capture and compare operation Four Periodical Interrupt Timers Generic 32-bit resolution timer Periodical interrupt generation One Quad Timer 4-channel generic 16-bit resolution timer i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 3, 08/2021 2 NXP Semiconductors