F1100 DATASHEET RF to IF Dual Downconverting Mixer 698 - 915 MHz F1100NBGI GENERAL DESCRIPTION FEATURES This document describes the specifications for the Dual Path for Diversity Systems TM IDTF1100 Zero-Distortion RF to IF Downconverting Ideal for Multi-Carrier Systems Mixer. This device is part of a series of downconverting MIMO friendly: -6 dBm min LO drive mixers covering all UTRA bands. See the Part Matrix 9 dB Gain for the details of all devices in the series. Ultra linear: +41 dBm IP3 (350 MHz IF) O Low NF ~10 dB The F1100 dual channel device operates with a single 200 output impedance 5V supply. It is optimized for operation in a Multi- Ultra high +13 dBm P1dB I carrier BaseStation Receiver for RF bands from 698 to Pin Compatible w/Existing solutions Pin Compatible w/Existing solutions 915 MHz with High Side Injection. IF frequencies from 6x6 36 pin package 150 to 450 MHz are supported. Nominally, the device PPoowweerr DDoowwnn mmooddee offers +41 dBm Output IP3 with 350 mA of I . CC Standard Mode: I = 350 mA CC COMPETITIVE ADVANTAGE In typical basestation receivers the mixer limits the DEVICE BLOCK DIAGRAM linearity performance for the entire receive system. The F1100 with Zero-Distortion technology dramatically improves the maximum IM interference that the BTS 3 can withstand at a desired Signal to Noise Ratio (SNR.) RF IN A IF OUT A IP3 : 7 dB O STBY RF VCO Bias Allows for higher RF Control 2 LO ADJ gain improving Sensitivity RF IN B IF OUT B PART MATRIX Part RF freq UTRA bands IF freq Typ. Injection range range Gain 55,,66,,88,,1122,,1133,,1144,,1177 F1100 698 - 915 150 - 450 9 High Side F1100 698 - 915 150 - 450 9 High Side ,,1199,,2200 ORDERING INFORMATION 5,6,8,12,13,14,17 F1102 400 - 1000 50 - 300 9.0 Both ,19,20 Omit IDT Tape & 0.8 mm height 1,2,3,4,9,10, 33, F1150 1700 - 2200 50 - 450 8.5 High Side prefix 34,35, 36, 37,39 Reel package 1 1,2,3,4,9,10, 21 , 1 F1152 1400 - 2200 24 , 33, 34,35, 50 - 350 8.5 Low Side 36, 37,39 IDTF1100NBGI8 F1162 2300 2700 7,38,40,41 50 500 8.8 Both Green 1 with High side injection RF product Line Industrial Temp range TM IDT Zero-Distortion Mixer 1 RevO, Feb 2013 F1100 DATASHEET RF to IF Dual Downconverting Mixer 698 - 915 MHz F1100NBGI ABSOLUTE MAXIMUM RATINGS VCC to GND -0.3V to +5.5V STBY -0.3V to (VCC + 0.3V) IF A+, IF B+, IF A-, IF B-, LO1 ADJ, LO2 ADJ -0.3V to (VCC + 0.3V) LO IN, LO IN ALT, RF A, RF B -0.3V to +0.3V IF BiasA, IF BiasB to GND -0.3V to +0.3V RF Input Power (RF A, RF B) +20dBm Continuous Power Dissipation 2.2W (Junction Ambient) +35C/W JA (Junction Case) The Case is defined as the exposed paddle +2.5C/W JC Operating Temperature Range (Case Temperature) T = -40C to +100C C Maximum Junction Temperature 150C Storage Temperature Range -65C to +150C Lead Temperature (soldering, 10s) . +260C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability TM IDT Zero-Distortion Mixer 2 RevO, Feb 2013