LMV321, LMV358, LMV324 Datasheet Low cost, low power, input/output rail-to-rail operational amplifiers LMV321ILT Features (SOT23-5) Operating range from V = 2.7 to 6 V CC Rail-to-rail input and output Extended V (V - 0.2 V to V + 0.2 V) icm DD CC LMV321RILT (SOT23-5) Low supply current (145 A) Gain bandwidth product (1 MHz) ESD tolerance (2 kV) LMV358IDT-LMV358IPT Applications (SO8, TSSOP8) Battery powered electronic equipment Personal medical care (glucose meters) Laptops LMV324IDT-LMV324IPT (SO14, TSSOP14) Description The LMV321/LMV324/LMV358 family (single, dual, and quad) answers the need for low cost, general-purpose operational amplifiers. They operate with voltages as low as 2.7 V and feature both input and output rail-to-rail, 145 A consumption current, and 1 MHz gain bandwidth product (GBP). With such a low consumption and a sufficient GBP for many applications, these Maturity status link op amps are well suited for any kind of battery supplied and portable equipment application. LMV321 The LMV321 device is housed in the space-saving 5-pin SOT23-5 package, which LMV324 simplifies board design. The SOT23-5 has two pinning configurations to answer all LMV358 application requirements. Related products LMV321L, For newer technological LMV324L, version LMV358L TSV851, For enhanced TSV852, performances TSV854 DS4539 - Rev 10 - September 2021 www.st.com For further information contact your local STMicroelectronics sales office.LMV321, LMV358, LMV324 Absolute maximum ratings and operating conditions 1 Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol Parameter Value Unit (1) V 7 CC Supply voltage (2) V id Differential input voltage 1 V V - 0.3 to DD V Input voltage in V + 0.3 CC T Operating free air temperature range -40 to 125 oper T Storage temperature -65 to 150 C stg T Maximum junction temperature 150 j SOT23-5 250 SO8 125 (3) R TSSOP8 120 thja Thermal resistance junction-to-ambient SO14 103 TSSOP14 100 C/W SOT23-5 81 SO8 40 (3) R TSSOP8 37 thjc Thermal resistance junction-to-case SO14 31 TSSOP14 32 (4) 2 kV HBM: human body model (5) ESD MM: machine model 200 V (6) CDM: charged device model 1.5 kV Lead temperature (soldering, 10 s) 250 C (7) Output short-circuit duration See 1. All voltage values, except differential voltage are with respect to network terminal. 2. The differential voltage is the non-inverting input terminal with respect to the inverting input terminal. If V > 1 V, the id maximum input current must not exceed 1 mA. In this case (V > 1 V), an input series resistor must be added to limit id input current. 3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. All values are typical. 4. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 k resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 ). This is done for all couples of connected pin combinations while the other pins are floating. 6. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins. No value specified for CDM on SOT23-5 package. The value is given for SO8 and TSSOP packages. 7. Short-circuits from the output to V can cause excessive heating. The maximum output current is approximately 48 mA, CC independent of the magnitude of V . Destructive dissipation can result from simultaneous short-circuits on all amplifiers. CC DS4539 - Rev 10 page 2/17