CAT25128 128-Kb SPI Serial CMOS EEPROM Description The CAT25128 is a 128Kb Serial CMOS EEPROM device internally organized as 16Kx8 bits. This features a 64byte page write CAT25128 Table 1. ABSOLUTE MAXIMUM RATINGS Parameters Ratings Units Operating Temperature 45 to +130 C Storage Temperature 65 to +150 C Voltage on any Pin with Respect to Ground (Note 1) 0.5 to +6.5 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The DC input voltage on any pin should not be lower than 0.5 V or higher than V + 0.5 V. During transitions, the voltage on any pin may CC undershoot to no less than 1.5 V or overshoot to no more than V + 1.5 V, for periods of less than 20 ns. CC Table 2. RELIABILITY CHARACTERISTICS (Note 2) Symbol Parameter Min Units N (Notes 3, 4) Endurance 1,000,000 Program / Erase Cycles END T Data Retention 100 Years DR 2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AECQ100 and JEDEC test methods. 3. Page Mode, V = 5 V, 25C. CC 4. The new product revision (E) uses ECC (Error Correction Code) logic with 6 ECC bits to correct one bit error in 4 data bytes. Therefore, when a single byte has to be written, 4 bytes (including the ECC bits) are reprogrammed. It is recommended to write by multiple of 4 bytes in order to benefit from the maximum number of write cycles. Table 3. D.C. OPERATING CHARACTERISTICS MATURE PRODUCT (V = 1.8 V to 5.5 V, T = 40C to +85C and V = 2.5 V to 5.5 V, T = 40C to +125C, unless otherwise specified.) CC A CC A Symbol Parameter Test Conditions Min Max Units I Supply Current Read, V = 5.5 V, 10 MHz / 40C to 85C 2 mA CCR CC (Read Mode) SO open 5 MHz / 40C to 125C 2 mA I Supply Current Write, V = 5.5 V, 10 MHz / 40C to 85C 4 mA CCW CC (Write Mode) SO open 5 MHz / 40C to 125C 4 mA I Standby Current V = GND or V , CS = V , T = 40C to +85C 1 A SB1 IN CC CC A WP = V , HOLD = V , CC CC T = 40C to +125C 3 A V = 5.5 V A CC I Standby Current V = GND or V , CS = V , T = 40C to +85C 4 A SB2 IN CC CC A WP = GND, HOLD = GND, T = 40C to +125C 5 A V = 5.5 V A CC I Input Leakage Current V = GND or V 2 2 A L IN CC I Output Leakage CS = V , T = 40C to +85C 1 1 A LO CC A Current V = GND or V OUT CC T = 40C to +125C 1 2 A A V Input Low Voltage 0.5 0.3 V V IL CC V Input High Voltage 0.7 V V + 0.5 V IH CC CC V Output Low Voltage V > 2.5 V, I = 3.0 mA 0.4 V OL1 CC OL V Output High Voltage V > 2.5 V, I = 1.6 mA V 0.8 V V OH1 CC OH CC V Output Low Voltage V > 1.8 V, I = 150 A 0.2 V OL2 CC OL V Output High Voltage V > 1.8 V, I = 100 A V 0.2 V V OH2 CC OH CC