DATASHEET RF to IF Dual Downconverting Mixer 1700 - 2200 MHz F1150NBGI FEATURES GENERAL DESCRIPTION Dual Path for Diversity Systems This document describes the specifications for the TM Ideal for Multi-Carrier Systems IDTF1150 Zero-Distortion RF to IF Downconverting 8.5 dB Gain (200 MHz IF) Mixer. This device is part of a series of downconverting Ultra linear +38 dBm IP3 (350 MHz IF) mixers offered with high side or low side injection O Ultra linear ++4400 ddBBmm IIPP33 ((220000 MMHHzz IIFF)) options for all UTRA bands. See the Part Matrix for the OO Low NF < 10 dB details of all devices in this series. 200 output impedance The F1150 dual channel device is designed to operate Ultra high +13 dBm P1dB I with a single 5V supply. It is optimized for operation in PPiinn CCoommppaattiibbllee with existing solutions a Multi-mode, Multi-carrier BaseStation Receiver for RF 6x6 36 pin package bands from 1700 - 2200 MHz with High Side Injection. Power Down mode Power Down mode IF frequencies from 50 to 450 MHz are supported. < 200 nsec settling from Power Down Nominally, the device offers +40 dBm Output IP3 with Minimizes Synth pulling in Standby Mode 335 mA of I . Alternately one can adjust 4 resistor CC Low Current Mode : II == 223355 mmAA CCCC values and a toggle pin to run the device in low current Standard Mode: I = 335 mA CC mode with +36 dBm Output IP3 and 235 mA of I . CC COMPETITIVE ADVANTAGE DEVICE BLOCK DIAGRAM In typical basestation receivers the RF to IF mixer dominates the linearity performance for the entire receive system. Zero-Distortion mixers dramatically improve the maximum signal levels (IM tones) that the RF IN A 3 BTS can withstand at a desired Signal to Noise Ratio IF OUT A (SNR.) Alternately, one can run the device in Low Current Mode to reduce Power consumption significantly. STBY RF VCO Bias 2 IDTs innovative design allows realization of either LO ISET Control benefit. LCMODE IP3 : 5 dB STD Mode, O RF IN B 2 dB LC Mode IF OUT B Dissipation: 40% LC Mode, 12% STD Mode Allows for higher RF gain improving Sensitivity ORDERING INFORMATION PART MATRIX Omit IDT Tape & Part RF freq UTRA bands IF freq Typ. Injection 0.8 mm height range range Gain prefix Reel package 5,6,8,12,13,14,17 F1100 698 - 915 50 - 450 8.5 High Side ,19,20 5,6,8,12,13,14,17 F1102 698 - 915 50 - 250 8.5 Both ,19,20 IDTF1150NBGI8 11,,22,,33,,44,,99,,1100,, 3333,, F1150 1700 - 2200 50 - 450 8.5 High Side F1150 1700 - 2200 50 - 450 8.5 High Side 3344,,3355,, 3366,, 3377,,3399 Green RF product Line Industrial 1,2,3,4,9,10,11 1 1 F1152 1400 - 2200 21 , 24 , 33, 50 - 350 8.4 Low Side Temp range 34,35, 36, 37,39 2 F1162 2200 2700 7,38,40,41 50 500 8.9 Both 1 with High side injection 2 With High side or Low side injection TM IDT Zero-Distortion Mixer 1 Rev2, July 2012 DATASHEET RF to IF Dual Downconverting Mixer 1700 - 2200 MHz F1150NBGI ABSOLUTE MAXIMUM RATINGS VCC to GND -0.3V to +5.5V STBY, LC -0.3V to (VCC + 0.3V) MODE IF A+, IF B+, IF A-, IF B-, LO IN -0.3V to (VCC + 0.3V) LO1 ADJ, LO2 ADJ, IF BiasA, IF BiasB to GND -0.3V to +1.2V RF Input Power (RF IN A+, A-, B+, B- ) +20dBm Continuous Power Dissipation 2.2W (Junction Ambient) +35C/W JA (Junction Case) The Case is defined as the exposed paddle +2.1C/W JC Operating Temperature Range (Case Temperature) T = -40C to +100C C Maximum Junction Temperature 150C Storage Temperature Range -65C to +150C Lead Temperature (soldering, 10s) . +260C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. TM IDT Zero-Distortion Mixer 2 Rev2, July 2012